Search Results

This paper summarizes an investigation of reductions in exhaust emission levels attainable using various techniques appropriate to gasoline engines used in vehicles over 14,000 lbs GVW. Of the eight gasoline engines investigated, two were evaluated parametrically resulting in an oxidation and reduction catalyst “best combination” configuration. Four of the engines were evaluated in an EGR plus oxidation catalyst configuration, and two involved only baseline tests. Test procedures used in evaluating the six “best combination” configurations include: three engine emission test procedures using an engine dynamometer, a determination of vehicle driveability, and two vehicle emission test procedures using a chassis dynamometer. Dramatic reductions in emissions were attained with the catalyst “best combination” configurations. Engine durability, however, was not investigated.

Cooled Exhaust Gas Recirculation (EGR) technology provides significant benefits such as better cycle efficiency, knock tolerance and lower NOx/PM emissions. However, EGR dilution also poses challenges in terms of combustion stability, power density and control. Conventional control schemes for EGR engines rely on a differential pressure sensor combined with an orifice flow model to estimate EGR flow rate. While EGR rate is an important quantity, intake O2 mass fraction may be a better indication of EGR, capturing quantity as well as “quality” of EGR. SwRI has successfully used intake O2 mass fraction as a controlled state to manage several types of EGR engines - dual loop EGR diesel engines, low pressure loop /dedicated EGR (D-EGR) gasoline engines as well as dual fuel engines. Several suppliers are currently developing intake O2 sensors but they typically suffer from limited accuracy, response time and reliability. Also, addition of a new sensor implies increased production costs.

An investigation was performed to identify the benefits of cooled exhaust gas recirculation (EGR) when applied to a potential ethanol flexible fuelled vehicle (eFFV) engine. The fuels investigated in this study represented the range a flex-fuel engine may be exposed to in the United States; from 85% ethanol/gasoline blend (E85) to regular gasoline. The test engine was a 2.0-L in-line 4 cylinder that was turbocharged and port fuel injected (PFI). Ethanol blended fuels, including E85, have a higher octane rating and produce lower exhaust temperatures compared to gasoline. EGR has also been shown to decrease engine knock tendency and decrease exhaust temperatures. A natural progression was to take advantage of the superior combustion characteristics of E85 (i.e. increase compression ratio), and then employ EGR to maintain performance with gasoline. When EGR alone could not provide the necessary knock margin, hydrogen (H2) was added to simulate an onboard fuel reformer.

Increasingly stringent emissions regulations require that modern diesel aftertreatment systems must warm up and begin controlling emissions shortly after startup. While several new aftertreatment technologies have been introduced that focus on lowering the aftertreatment activation temperature, the engine system still needs to provide thermal energy to the exhaust for cold start. A study was conducted to evaluate several engine technologies that focus on improving the thermal energy that the engine system provides to the aftertreatment system while minimizing the impact on fuel economy and emissions. Studies were conducted on a modern common rail 3L diesel engine with a custom dual loop EGR system. The engine was calibrated for low engine-out NOx using various combustion strategies depending on the speed/load operating condition.

Low-pressure loop exhaust gas recirculation (LP- EGR) combined with higher compression ratio, is a technology package that has been a focus of research to increase engine thermal efficiency of downsized, turbocharged gasoline direct injection (GDI) engines. Research shows that the addition of LP-EGR reduces the propensity to knock that is experienced at higher compression ratios [1]. To investigate the interaction and compatibility between increased compression ratio and LP-EGR, a 1.6 L Turbocharged GDI engine was modified to run with LP-EGR at a higher compression ratio (12:1 versus 10.5:1) via a piston change. This paper presents the results of the baseline testing on an engine run with a prototype controller and initially tuned to mimic an original equipment manufacturer (OEM) baseline control strategy running on premium fuel (92.8 anti-knock index).

This paper summarizes a laboratory effort toward reducing nine-mode cycle composite emissions and fuel consumption in a heavy-duty gasoline engine, while retaining current durability performance. Evaluations involved standard carburetors, a Dresserator inductor, a Bendix electronic fuel injection system, exhaust manifold thermal reactors, and exhaust gas recirculation, along with other components and engine operating parameters. A system consisting of electronic fuel injection, thermal reactors with air injection and exhaust gas recirculation, was assembled which met specified project goals. An oxidation catalyst was included as an add-on during the service accumulation demonstration. In addition, the driveability of this engine configuration was demonstrated.

Dedicated-EGR™ (D-EGR™) is a concept where the exhaust of one dedicated cylinder (D-Cyl) is routed into the intake thus producing EGR to be used by the whole engine. The D-Cyl operates rich of stochiometric which produces syngas that enhances the EGR stream permitting faster combustion and greater knock mitigation. Operating an engine using D-EGR improves the knock resistance which can permit a higher compression ratio (CR) thereby increasing efficiency. One challenge of traditional D-EGR is that the D-Cyl combustion becomes unstable operating with both rich and EGR dilute conditions. Therefore, the ‘Split Intake D-EGR’ concept seeks to resolve this problem by feeding fresh air to the D-Cyl, thus allowing even richer operation in the D-Cyl which further increases the H2 and CO yield thereby enhancing the efficiency benefits.

Dedicated exhaust gas recirculation (D-EGR®) concept developed by Southwest Research Institute (SwRI) has demonstrated a thermal efficiency increase on many spark-ignited engines at both low and high load conditions. The syngas (H2+CO) produced in the dedicated cylinder (D-cyl) by rich combustion helps to stabilize combustion at highly dilute conditions at low loads and mitigate knock at high loads. The dedicated cylinder with 25% EGR can typically run up to equivalence ratio of 1.4, beyond which the combustion becomes unstable. By injecting fresh air near the spark plug gap at globally rich conditions, a locally lean or near-stoichiometric mixture can be achieved, thus facilitating the ignitability of the mixture and increasing combustion stability. With more stable combustion a richer global mixture can be introduced into the D-cyl to generate higher concentrations of syngas. This in turn can further improve the engine thermal efficiency.

Increased in-cylinder hydrogen levels have been shown to improve burn durations, combustion stability, HC emissions and knock resistance which can directly translate into enhanced engine efficiency. External fuel reformation can also be used to increase the hydrogen yield. During the High-Efficiency, Dilute Gasoline Engine (HEDGE) consortium at Southwest Research Institute (SwRI), the potential of increased hydrogen production in a dedicated-exhaust gas recirculation (D-EGR) engine was evaluated exploiting the water gas shift (WGS) and steam reformation (SR) reactions. It was found that neither approach could produce sustained hydrogen enrichment in a real exhaust environment, even while utilizing a lean-rich switching regeneration strategy. Platinum group metal (PGM) and Ni WGS catalysts were tested with a focus on hydrogen production and catalyst durability.

Homogeneous Charge Compression Ignition (HCCI) experiments were performed in a variable compression ratio single cylinder engine. This is the fourth paper resulting from work performed at Southwest Research Institute in this HCCI engine. The experimental variables, in addition to speed and load, included compression ratio, EGR level, intake manifold pressure and temperature, fuel introduction location, and fuel composition. Mixture preparation and start of reaction control were identified as fundamental problems that required non-traditional mixture preparation and control strategies. The effects of the independent variable on the start of reaction have been documented. For fuels that display significant pre-flame reactions, the start of the pre-flame reactions is controlled primarily by the selection of the fuel and the temperature history of the fuel air mixture.

This paper describes the ongoing homogeneous charge compression ignition (HCCI) research being carried out at Southwest Research Institute (SwRI). Summaries of the results of testing to date are presented and discussed. HCCI is a process whereby a premixed charge of diesel fuel and air is admitted into the power cylinder and compression ignited. Ignition occurs homogeneously throughout the cylinder. HCCI reduces flame temperatures and oxides of nitrogen (NOx) emissions. The lack of fuel rich zones within the cylinder eliminates soot formation (1-pull Bosch smoke numbers of 0, 5-pull = 0). The limits of HCCI start of combustion timing are defined by knock before top dead center (BTDC) and misfire after top dead center (ATDC). Stable and repeatable HCCI combustion has been demonstrated over a wide range of air-fuel (A/F) ratios, intake temperatures, compression ratios (CR), exhaust gas recirculation (EGR) rates, and for two fuels. A/F ratios of 14 to 80 are possible.

Large reductions in low-load NOx emissions can be obtained by replacing conventional Diesel or spark ignited combustion by HCCI combustion in reciprocating engines. Currently, HCCI combustion is limited to operating conditions with lean air/fuel ratios or large amounts of EGR. However, a numerical model shows that, even if high equivalence ratio HCCI operation were satisfactorily attained, the NOx reduction potential vs. DI-Diesel combustion would be much smaller. Thus, high-load HCCI operation may best be obtained through highly boosted fuel-lean operation. Alternatively, HCCI combustion may be suited well for “dual mode” engine applications, in which spark ignition or conventional Diesel combustion is used to obtain full load. Avoiding wall impingement with heavy fuels is critical for achieving good emissions and fuel consumption, and it appears that a large degree of mixture inhomogeneity can be tolerated from a NOx benefit standpoint.

A single-cylinder, direct-injection diesel engine was modified to operate on compression ignition of homogenous mixtures of diesel fuel and air. Previous work has indicated that extremely low emissions and high efficiencies are possible if ignition of homogeneous fuel-air mixtures is accomplished. The limitations of this approach were reported to be misfire and knock. These same observations were verified in the current work. The variables examined in this study included air-fuel ratio, compression ratio, fresh intake air temperature, exhaust gas recirculation rate, and intake mixture temperatures. The results suggested that controlled homogeneous charge compression ignition (HCCI) is possible. Compression ratio, EGR rate, and air fuel ratio are the practical controlling factors in achieving satisfactory operation. It was found that satisfactory power settings are possible with high EGR rates and stoichiometric fuel-air mixtures.

Homogeneous Charge Compression Ignition (HCCI) combustion can be made to occur in a four-stroke engine with smooth and even combustion under some circumstances. It offers the possibility of light load operation without throttling, thus giving fuel economy like a diesel, in the same engine allowing full load operation with homogeneous charge, thus giving a power density comparable to a gasoline engine. This paper gives results of an experimental program in which the ranges of permissible values of the operating parameters were defined for HCCI operation of a four-stroke engine. It was found that HCCI required high exhaust gas recirculation (EGR) rates (in the range of 13 to 33 percent) and high intake temperatures (greater than 370°C). Under the right conditions HCCI combustion produced fuel economy results comparable with a D.I. diesel engine (ISFC in the range 180 to 200 g/kWh).

A series of tests were performed on a gasoline powered engine with a Dedicated EGR® (D-EGR®) system. The results showed that changes in engine performance, including improvements in burn rates and stability and changes in emissions levels could not be adequately accounted for solely due to the presence of reformate in the EGR stream. In an effort to adequately characterize the engine's behavior, a new parameter was developed, the Total Inert Dilution Ratio (TIDR), which accounts for the changes in the EGR quality as inert gases are replaced by reactive species such as CO and H2.

The use of cooled EGR in gasoline engines improves the fuel efficiency of the engine through a variety of mechanisms, including improving the charge properties (e.g. the ratio of specific heats), reducing knock and enabling higher compression ratio operation and, at part loads conditions in particular, reducing pumping work. One of the limiting factors on the level of improvement from cooled EGR is the ability of the ignition system to ignite a dilute mixture and maintain engine stability. Previous work from SwRI has shown that, by increasing the ignition duration and using a continuous discharge ignition system, an improved ignition system can substantially increase the EGR tolerance of an engine [1, 2]. This improvement comes at a cost, however, of increased ignition system energy requirements and a potential decrease in spark plug durability. This work examines the impact of engine operating parameters on the ignition energy requirements under high dilution operation.

Particulate matter (PM) and NOX are two major pollutants generated by diesel engines. Modern diesel aftertreatment systems include selective catalytic reduction (SCR) technology that helps reduce tailpipe NOX emissions when coupled with diesel exhaust fluid (DEF/urea) injection. However, this process also results in the formation of urea derived byproducts that can influence non-volatile particle number (PN) measurement conducted in accordance with the European Union (EU) Particle Measurement Program (PMP) protocol. In this program, an experimental investigation of the impact of DEF injection on tailpipe PN and its implications for PMP compliant measurements was conducted using a 2015 model year 6.7 L diesel engine equipped with a diesel oxidation catalyst, diesel particulate filter and SCR system. Open access to the engine controller was available to manually override select parameters.

In response to the sensitivity to diesel aftertreatment costs in the medium duty market, a John Deere 4045 was converted to burn gasoline with high levels of EGR. This presented some unique challenges not seen in light duty gasoline engines as the flat head and diesel adapted ports do not provide optimum in-cylinder turbulence. As the bore size increases, there is more opportunity for knock or incomplete combustion to occur. Also, the high dilution used to reduce knock slows the burn rates. In order to speed up the burn rates, various levels of swirl were investigated. A four valve head with different levels of port masking showed that increasing the swirl ratio decreased the combustion duration, but ultimately ran into high pumping work required to generate the desired swirl. A two valve head was used to overcome the breathing issue seen in the four valve head with port masking.

Commercial vehicles are moving in the direction of improving brake thermal efficiency while also meeting future diesel emission requirements. This study is focused on improving efficiency by replacing the variable geometry turbine (VGT) turbocharger with a high-efficiency fixed geometry turbocharger. Engine-out (EO) NOX emissions are maintained by providing the required amount of exhaust gas recirculation (EGR) using a 48 V motor driven EGR pump downstream of the EGR cooler. This engine is also equipped with cylinder deactivation (CDA) hardware such that the engine can be optimized at low load operation using the combination of the high-efficiency turbocharger, EGR pump and CDA. The exhaust aftertreatment system has been shown to meet 2027 emissions using the baseline engine hardware as it includes a close coupled light-off SCR followed by a downstream SCR system.

Exhaust gas recirculation (EGR) has long been used in gasoline and light-duty diesel engines as a NOx reduction tool. Recently imposed emission regulations led several heavy-duty diesel engine manufacturers to adopt EGR as part of their strategy to reduce NOx. The effectiveness of this technology has been widely documented, with NOx reduction in the range of 40 to 50 percent having been recorded. An inevitable consequence of this strategy is an increase in particulate emission, especially if EGR was used in high engine load modes. Selective catalytic reduction (SCR), a method for NOx reduction, is widely used in stationary applications. There is growing interest and activity to apply it to mobile fleets equipped with heavy-duty diesel engines. Results of this work indicate that SCR has the potential to dramatically reduce NOx in diesel exhaust. Reductions greater than 70 percent were reported by several including the Institute's previous work (SAE Paper No. 1999-01-3564).